TS Porsche LWB 918 Seat Recliner Brackets 911 991 GT3 GT3RS GT4
£189.99 inc VAT
25 in stock
Trackspec Autosports
Porsche LWB 918 Seat Recliner Brackets
Black -Anodized 911 991 GT3 GT3RS GT4
* Note * One set reclines one Seat
These brackets raise your Porsche LWB seats approximately 1″ in the front, reclining the seat. One order provides brackets to adjust ONE seat. For owners who feel the stock seat position is too upright. Installation instructions are supplied.
-
6061-T6 Billet Aluminum
-
Made in the USA
-
One set reclines one seat.
-
All mounting hardware is included.
-
Raises your Porsche Carbon Fiber LWB seats approximately 1″ in the front
-
For owners who feel the stock seat position is too upright.
-
991.1 991.2 GT3 GT3RS GT4
kit contents
One kit will work on either driver or passenger seat.
-
x1 inner bracket
-
x1 outer bracket
-
x2 M6 bolts
-
x2 M10 bolts
-
x2 M10 washers
-
x2 M10 nuts
tools needed
-
3/8” ratchet
-
E12 socket (3/8″ drive)
-
6mm Allen
-
8mm Allen
-
10mm wrench
-
16mm wrench
-
17mm wrench
-
Blue Loctite or Medium strength thread locker
ATTN: 718 GT4 Owners
The 718 GT4 has less rearward clearance. Due to the seat being reclined back, the seat will interfere with the firewall if it adjusted all the way back and lower than the highest setting. TO PREVENT DAMAGING YOUR SEAT, MAKE SURE YOU HAVE REAR CLEARANCE BEFORE LOWERING THE SEAT HEIGHT.
Seat at highest position: 8.5″ of forward to back movement (full range)
Seat at middle height position: 7.5″ of forward to back movement (12% less)
Seat at lowest position: 6.5″ of forward to back movement (24% less)
Installation Instructions
Step 1: Disconnect Battery
Remove panel in trunk to access battery. Disconnect NEGATIVE (-) terminal using 10mm wrench.
Step 2: Remove Seat Bolts
Use the E12 socket to remove all four seat bolts. Slide seat all the way back to access bolts 1&2. Slide seat all the way forward to access bolts 3&4
Step 3: Unbolt Seatbelt
Use the 17mm wrench to remove seat belt from seat. A plastic cap will need to be pulled off first.
Step 4: Disconnect Yellow Plug
Under the seat, disconnect the yellow plug by first pulling up on the black tab to unlock it.
Drape a towel over the side sill to prevent scratches and carefully remove seat.
Step 5: Unbolt Pivoting Arm
Remove bolt from the pivoting arm on both sides using the 16mm wrench and 8mm Allen.
Step 6: Install Seat Recliner Brackets
-
Install recliner brackets as shown. Start threading the supplied M6 bolt into the bracket through the small hole in the seat rail, but do not tighten. On the right side, you will need to remove a wire harness clip. You can leave it loose or tie it off. Install supplied M10 bolt through seat rail and bracket. Secure with M10 washer and Nyloc nut , but do not tighten. Once both bolts are in place, tighten down the M6 bolt to 72 in lbs (or hand tight), then the M10 bolt to 30 ft lbs.
-
Install pivoting arm to the riser with the shouldered part of the bolt on the plastic bushing. If installed correctly, the nut will be on the inside of the seat (opposite of how it was originally). Use medium strength thread locker on this nut and bolt and torque to 30 ft bs.
Step 7: Reinstall Seat
Follow directions in reverse to reinstall seat.
NOTE: Hardware in install photos may look different than you were supplied. Hardware shown under “kit contents” at the top of this page are accurate.
| Weight | 0.00000000 kg |
|---|
Only logged in customers who have purchased this product may leave a review.
Related products
PORSCHE SEAT BRACKETS
TS Porsche LWB 918 Seat Recliner Brackets 911 991 GT3 GT3RS GT4 (Set of 2 / 2x Seats)
Reviews
There are no reviews yet.